Name*
First
Last
Email* B. GENERAL RIG SPECIFICATIONS Comments
B.1 DERRICK AND SUBSTRUCTURE Comments
B.1.1 Derrick/Mast Comments
B.1.1 Main Comments
Make
Type IMPERIAL: Conventional / Hydraulic / etc. | METRIC: Conventional / Hydraulic / etc.
Model
Rated for wind speed
With full set back IMPERIAL: knots | METRIC: knots
With no set back IMPERIAL: knots | METRIC: knots
Height IMPERIAL: ft | METRIC: m
Dimensions of base IMPERIAL: ft x ft | METRIC: m x m
Dimensions of crown IMPERIAL: ft x ft | METRIC: m x m
Dimensions of water table IMPERIAL: ft x ft | METRIC: m x m
Gross nominal capacity IMPERIAL: lt | METRIC: mt
Dynamic load capacity IMPERIAL: lt | METRIC: mt
Static load capacity IMPERIAL: lt | METRIC: mt
Maxiumum simultaneous load capacity (Main/Aux hook loads) IMPERIAL: lt | METRIC: mt
Maximum Number of lines IMPERIAL: no. | METRIC: no.
Ladders with safety cages and rests IMPERIAL: yes/no | METRIC: yes/no
Platform for crown sheave access IMPERIAL: yes/no | METRIC: yes/no
Counter balance, system for rig tongs and pipe spinning tong IMPERIAL: yes/no | METRIC: yes/no
Lighting system explosion proof IMPERIAL: yes/no | METRIC: yes/no
Clear working height to underside of water table IMPERIAL: ft | METRIC: m
Height available from rotary table to below top drive IMPERIAL: ft | METRIC: m
Offline activity capabilities (dual handling, dual derrick, etc.)
Gas vent line diameter IMPERIAL: OD / ID in | METRIC: OD / ID mm
Derrick steelwork / bolting hot dip galvanized IMPERIAL: yes/no | METRIC: yes/no
V-Door height (Max clearance) IMPERIAL: ft | METRIC: m
Derrick Elevator IMPERIAL: yes/no | METRIC: yes/no
B.1.1 Auxillary Comments
Make
Type IMPERIAL: Conventional / Hydraulic / etc. | METRIC: Conventional / Hydraulic / etc.
Rated for wind speed
With full set back IMPERIAL: knots | METRIC: knots
With no set back IMPERIAL: knots | METRIC: knots
Height IMPERIAL: ft | METRIC: m
Dimensions of base IMPERIAL: ft x ft | METRIC: m x m
Dimensions of crown IMPERIAL: ft x ft | METRIC: m x m
Dimensions of water table IMPERIAL: ft x ft | METRIC: m x m
Gross nominal capacity IMPERIAL: lt | METRIC: lt
Dynamic load capacity IMPERIAL: lt | METRIC: mt
Static load capacity IMPERIAL: lt | METRIC: mt
Maxiumum simultaneous load capacity (Main/Aux hook loads) IMPERIAL: lt | METRIC: mt
Maximum Number of lines IMPERIAL: no. | METRIC: no.
Ladders with safety cages and rests IMPERIAL: yes/no | METRIC: yes/no
Platform for crown sheave access IMPERIAL: yes/no | METRIC: yes/no
Lighting system explosion proof IMPERIAL: yes/no | METRIC: yes/no
Clear working height to underside of water table IMPERIAL: ft | METRIC: m
Height available from rotary table to below top drive IMPERIAL: ft | METRIC: m
Offline activity capabilities (dual handling, dual derrick, etc.)
Gas vent line diameter IMPERIAL: OD / ID in | METRIC: OD / ID mm
Derrick steelwork / bolting hot dip galvanized IMPERIAL: yes/no | METRIC: yes/no
V-Door height (Max clearance) IMPERIAL: ft | METRIC: m
Derrick Elevator IMPERIAL: yes/no | METRIC: yes/no
B.1.2 Racking Platform Comments
B.1.2 Main Comments
Make
Type
Maximum racking height IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 5 1/2” DP IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 5 7/8” DP IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 6 5/8” DP IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 6 3/4” DC IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 8” DC IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 9 1/2” DC IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 26”, 22” or 20” Casing IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 16", 14”, 13 5/8” or 13 3/8”Casing IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 11 3/4", 10 3/4” , 9 5/8” or 7” Casing IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 6 5/8” Drill Pipe Riser IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 7” or 3 1/2” Production String IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of Drilling BHA IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of other equipment (description) IMPERIAL: # stands / ft | METRIC: # stands / m
Fingerboard latch system IMPERIAL: yes/no | METRIC: yes/no
B.1.2 Auxillary Comments
Make
Type
Maximum racking height IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 5 1/2” DP IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 5 7/8” DP IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 6 5/8” DP IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 6 3/4” DC IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 8” DC IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 9 1/2” DC IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 26”, 22” or 20” Casing IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 16", 14”, 13 5/8” or 13 3/8”Casing IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 11 3/4", 10 3/4” , 9 5/8” or 7” Casing IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 6 5/8” Drill Pipe Riser IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of 7” or 3 1/2” Production String IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of Drilling BHA IMPERIAL: # stands / ft | METRIC: # stands / m
Racking platform capacity of other equipment (description) IMPERIAL: # stands / ft | METRIC: # stands / m
Fingerboard latch system IMPERIAL: yes/no | METRIC: yes/no
B.1.3 Racking Arm Comments
B.1.3 Main Comments
Make
Type
Quantity IMPERIAL: no. | METRIC: no.
Racking or automatic racking system and rig floor automation IMPERIAL: yes/no | METRIC: yes/no
Describe limitations IMPERIAL: text | METRIC: text
Max diameter IMPERIAL: in | METRIC: mm
Max stand weight IMPERIAL: lb | METRIC: kg
Usable with non mag steel IMPERIAL: yes/no | METRIC: yes/no
B.1.3 Auxillary Comments
Make
Type
Quantity IMPERIAL: no. | METRIC: no.
Racking or automatic racking system and rig floor automation IMPERIAL: yes/no | METRIC: yes/no
Describe limitations IMPERIAL: text | METRIC: text
Max diameter IMPERIAL: in | METRIC: mm
Max stand weight IMPERIAL: lb | METRIC: kg
Usable with non mag steel IMPERIAL: yes/no | METRIC: yes/no
B.1.4 Casing Stabbing Board Comments
Make
Type
Adjustable from/to height above rotary (upper racking platform) IMPERIAL: ft/ft | METRIC: m/m
Adjustable from/to height above rotary (lower racking platform) IMPERIAL: ft/ft | METRIC: m/m
B.1.5 Substructure Comments
B.1.5 Main Comments
Dual Derrick / Dual Activity IMPERIAL: yes/no | METRIC: yes/no
Make
Type
Height (above main deck) IMPERIAL: ft | METRIC: m
Length IMPERIAL: ft | METRIC: m
Width IMPERIAL: ft | METRIC: m
Setback capacity IMPERIAL: lt | METRIC: lt
Simultaneous setback + hook load capacity IMPERIAL: lt + lt | METRIC: lt + lt
Clear height below rotary table beams IMPERIAL: ft | METRIC: m
Set back allowance during field moves IMPERIAL: max load ton | METRIC: max load ton
Hook load IMPERIAL: max load ton | METRIC: max load ton
Pipe setback load IMPERIAL: max load ton | METRIC: max load ton
Riser setback load IMPERIAL: max load ton | METRIC: max load ton
Rotary hang off IMPERIAL: max load ton | METRIC: max load ton
Riser tension IMPERIAL: max load ton | METRIC: max load ton
B.1.5 Auxillary Comments
Make
Type
Height (above main deck) IMPERIAL: ft | METRIC: m
Length IMPERIAL: ft | METRIC: m
Width IMPERIAL: ft | METRIC: m
Setback capacity IMPERIAL: lt | METRIC: lt
Simultaneous setback + hook load capacity IMPERIAL: lt + lt | METRIC: lt + lt
Clear height below rotary table beams IMPERIAL: ft | METRIC: m
Set back allowance during field moves IMPERIAL: max load ton | METRIC: max load ton
Hook load IMPERIAL: max load ton | METRIC: max load ton
Pipe setback load IMPERIAL: max load ton | METRIC: max load ton
Riser setback load IMPERIAL: max load ton | METRIC: max load ton
Rotary hang off IMPERIAL: max load ton | METRIC: max load ton
Riser tension IMPERIAL: max load ton | METRIC: max load ton
B.1.6 Weather Proofing / Winterization Comments
Rig floor windbreaks height IMPERIAL: ft | METRIC: m
Derrickman windbreaks height IMPERIAL: ft | METRIC: m
Totally enclosed rig floor IMPERIAL: yes/no | METRIC: yes/no
Totally enclosed rig floor IMPERIAL: yes/no | METRIC: yes/no
Pipe heat tracing IMPERIAL: ft | METRIC: m
B.1.7 Derrick TV Camera System Comments
Camera located at
Make
Type
Zoom/Pan/Tilt-function IMPERIAL: yes/no | METRIC: yes/no
Monitor located at
Remoted accessed IMPERIAL: yes/no | METRIC: yes/no
B.1.8 Derrickman's Escape System Comments
Model/Type
Quantity IMPERIAL: no. | METRIC: no.
Capacity IMPERIAL: lb | METRIC: kg
Manufacturer
B.2 DRAWWORKS AND ASSOCIATED EQUIPMENT Comments
B.2.1 Drawworks / Cylinder Hoisting System Comments
B.2.1 Main Comments
Dual drawworks capacity IMPERIAL: yes/no | METRIC: yes/no
Make
Type
Dimensions (L x W x H) IMPERIAL: in | METRIC: mm
Weight IMPERIAL: lb | METRIC: kg
Hoisting Capacity IMPERIAL: lt | METRIC: mt
Drawworks installed power IMPERIAL: hp | METRIC: kW
Maximum line pull
1st gear IMPERIAL: ton | METRIC: ton
2nd gear IMPERIAL: ton | METRIC: ton
3rd gear IMPERIAL: ton | METRIC: ton
4th gear / ADS IMPERIAL: ton | METRIC: ton
Fast line pull IMPERIAL: lb | METRIC: kg
Fastline stabiliser system
Manufacturer
Model
Type
Drawworks Drum
Drum diameter IMPERIAL: in | METRIC: mm
Drum capacity IMPERIAL: ft | METRIC: m
Wire diameter IMPERIAL: in | METRIC: mm
Spinning cathead type
Breakout cathead type
Crown block safety device IMPERIAL: yes/no | METRIC: yes/no
Make/Type
Selectable ram hoisting IMPERIAL: yes/no | METRIC: yes/no
Maximum rams per tower IMPERIAL: no. | METRIC: no.
Hoisting capacity with 2 rams
Low speed
High speed
Boost mode
Hoisting capacity with 3 rams
Low speed
High speed
Boost mode
Hoisting capacity with 4 rams
Low speed
High speed
Boost mode
Hoisting capacity with 5 rams
Low speed
High speed
Boost mode
B.2.1 Auxillary Comments
Dual drawworks capacity IMPERIAL: yes/no | METRIC: yes/no
Make
Type
Dimensions (L x W x H) IMPERIAL: in | METRIC: mm
Weight IMPERIAL: lb | METRIC: kg
Hoisting Capacity IMPERIAL: lt | METRIC: mt
Drawworks installed power IMPERIAL: hp | METRIC: kW
Maximum line pull
1st gear IMPERIAL: ton | METRIC: ton
2nd gear IMPERIAL: ton | METRIC: ton
3rd gear IMPERIAL: ton | METRIC: ton
4th gear / ADS IMPERIAL: ton | METRIC: ton
Fast line pull IMPERIAL: lb | METRIC: kg
Fastline stabiliser system
Manufacturer
Model
Type
Drawworks Drum
Drum diameter IMPERIAL: in | METRIC: mm
Drum capacity IMPERIAL: ft | METRIC: m
Wire diameter IMPERIAL: in | METRIC: mm
Spinning cathead type
Breakout cathead type
Crown block safety device IMPERIAL: yes/no | METRIC: yes/no
Make/Type
Selectable ram hoisting IMPERIAL: yes/no | METRIC: yes/no
Maximum rams per tower IMPERIAL: no. | METRIC: no.
Hoisting capacity with 2 rams
Low speed
High speed
Boost mode
Hoisting capacity with 3 rams
Low speed
High speed
Boost mode
Hoisting capacity with 4 rams
Low speed
High speed
Boost mode
Hoisting capacity with 5 rams
Low speed
High speed
Boost mode
B.2.2 Drawworks Utilities Comments
B.2.2 Main Comments
Anti-collision system IMPERIAL: yes/no | METRIC: yes/no
Make/Type
Drawworks Power
Manufacturer/Model
Nominal input power IMPERIAL: VAC/VDC | METRIC: VAC/VDC
Drawworks Motor Drive
Manufacturer/Model
Quantity IMPERIAL: no. | METRIC: no.
Power requirement IMPERIAL: VAC/VDC | METRIC: VAC/VDC
Rated output power continuous IMPERIAL: hp | METRIC: hp
Rated output power intermittent IMPERIAL: hp | METRIC: hp
Water supply for motors IMPERIAL: yes/no | METRIC: yes/no
Type IMPERIAL: fresh/sea | METRIC: fresh/sea
Flowrate IMPERIAL: gpm | METRIC: l / min
Transducers
Quantity IMPERIAL: no. | METRIC: no.
B.2.2 Auxillary Comments
Anti-collision system IMPERIAL: VAC/VDC | METRIC: VAC/VDC
Make/Type
Drawworks Power
Manufacturer/Model
Nominal input power IMPERIAL: VAC/VDC | METRIC: VAC/VDC
Drawworks Motor Drive
Manufacturer/Model
Quantity IMPERIAL: no. | METRIC: no.
Power requirement IMPERIAL: VAC/VDC | METRIC: VAC/VDC
Rated output power continuous IMPERIAL: hp | METRIC: hp
Rated output power intermittent IMPERIAL: hp | METRIC: hp
Water supply for motors IMPERIAL: yes/no | METRIC: yes/no
Type IMPERIAL: fresh/sea | METRIC: fresh/sea
Flowrate IMPERIAL: gpm | METRIC: l / min
Transducers
Quantity IMPERIAL: no. | METRIC: no.
B.2.3 Auxiliary Brake Comments
B.2.3 Main Comments
Make
Model
Type
Independent back-up system type
Water supply for brake IMPERIAL: yes/no | METRIC: yes/no
Type IMPERIAL: fresh/sea | METRIC: fresh/sea
Flowrate IMPERIAL: gpm | METRIC: l / min
B.2.3 Auxillary Comments
Make
Model
Type
Independent back-up system type
Water supply for brake IMPERIAL: yes/no | METRIC: yes/no
Type IMPERIAL: fresh/sea | METRIC: fresh/sea
Flowrate IMPERIAL: gpm | METRIC: l / min
B.2.4 Sandline Comments
B.2.4 Main Comments
Make
Length capacity IMPERIAL: ft | METRIC: m
Line size/type IMPERIAL: in | METRIC: mm
Breaking strength IMPERIAL: lt | METRIC: lt
Safe working load IMPERIAL: lt | METRIC: lt
Sand Line Drum
Drum diameter IMPERIAL: in | METRIC: mm
Drum capacity IMPERIAL: ft | METRIC: m
Wire diameter IMPERIAL: in | METRIC: mm
B.2.4 Auxillary Comments
Make
Length capacity IMPERIAL: ft | METRIC: m
Line size/type IMPERIAL: in | METRIC: mm
Breaking strength IMPERIAL: lt | METRIC: lt
Safe working load IMPERIAL: lt | METRIC: lt
Sand Line Drum
Drum diameter IMPERIAL: in | METRIC: mm
Drum capacity IMPERIAL: ft | METRIC: m
Wire diameter IMPERIAL: in | METRIC: mm
B.2.5 Slickline Comments
B.2.5 Main Comments
Make
Length capacity IMPERIAL: ft | METRIC: m
Line size/type IMPERIAL: in | METRIC: mm
Breaking strength IMPERIAL: lt | METRIC: lt
Safe working load IMPERIAL: lt | METRIC: lt
B.2.5 Auxillary Comments
Make
Length capacity IMPERIAL: ft | METRIC: m
Line size/type IMPERIAL: in | METRIC: mm
Breaking strength IMPERIAL: lt | METRIC: lt
Safe working load IMPERIAL: lt | METRIC: lt
B.2.6 Automatic Driller IMPERIAL: yes/no | METRIC: yes/no
Comments
Make
Type
B.2.7 Heave Motion Compensator IMPERIAL: passive / active | METRIC: passive / active
Comments
B.2.7 Main Comments
Make/Type
Sensitivity
Stroke / Performance
API rated capacity
Capacity in lock position
B.2.7 Auxillary Comments
Make/Type
Sensitivity
Stroke / Performance
API rated capacity
Capacity in lock position
B.2.8 Drawworks Control System Comments
B.2.8 Main Comments
Control Cabinets IMPERIAL: no. | METRIC: no.
Dimensions IMPERIAL: ft x ft x ft | METRIC: m x m x m
PLC type
B.2.8 Auxillary Comments
Control Cabinets IMPERIAL: no. | METRIC: no.
Dimensions IMPERIAL: ft x ft x ft | METRIC: m x m x m
PLC type
B.3 DERRICK HOISTING EQUIPMENT Comments
B.3.1 Crown Block Comments
Make
Type
Rated capacity IMPERIAL: lt | METRIC: lt
No. of sheaves IMPERIAL: no. | METRIC: no.
Sheave diameter IMPERIAL: in | METRIC: mm
Sheave grooved for line size IMPERIAL: in | METRIC: mm
Anti jump bar IMPERIAL: yes/no | METRIC: yes/no
B.3.2 Travel Block Comments
Make
Type
Rated capacity IMPERIAL: lt | METRIC: lt
No. of sheaves IMPERIAL: no. | METRIC: no.
Sheave diameter IMPERIAL: in | METRIC: mm
Sheave grooved for line size IMPERIAL: in | METRIC: mm
B.3.3 Hook Comments
Make
Type
Rated capacity IMPERIAL: lt | METRIC: lt
Complete with spring assembly/hook locking device IMPERIAL: yes/no | METRIC: yes/no
B.3.4 Drilling Line Comments
Diameter IMPERIAL: in | METRIC: mm
Type
Length (original) IMPERIAL: ft | METRIC: m
Support frame for drum/cover IMPERIAL: yes/no | METRIC: yes/no
Drilling line drum power driven IMPERIAL: yes/no | METRIC: yes/no
Spare reel drilling line IMPERIAL: yes/no | METRIC: yes/no
Location (rig, shore, etc.)
B.3.5 Anchor Dead Line Comments
Make
Type
Weight sensor IMPERIAL: yes/no | METRIC: yes/no
Number IMPERIAL: no | METRIC: no
Location
Hydraulic / Electric / etc
B.3.6 Drilling String Motion Compensator Comments
Make
Type
Stroke IMPERIAL: ft | METRIC: m
Capacity - compensated IMPERIAL: lt | METRIC: lt
Capacity - locked IMPERIAL: lt | METRIC: lt
B.3.7 Block Guidance System Comments
Make
Type
B.3.8 Retraction System For Traveling Block Comments
Make
Type
B.3.9 Hydraulic Cylinder Hoisting System Comments
Generation
Amount of cylinders IMPERIAL: no. | METRIC: no.
Compensating stroke IMPERIAL: ft | METRIC: m
Max hoisting capacity IMPERIAL: lt | METRIC: lt
B.4 ROTATING SYSTEM Comments
B.4.1 Rotary Table B.4.1 Main Comments
Make
Type
Maximum opening IMPERIAL: in | METRIC: mm
Rated capacity IMPERIAL: lb | METRIC: kg
Static load capacity IMPERIAL: lb | METRIC: kg
Rotating load capacity IMPERIAL: lb | METRIC: kg
Associated RPM IMPERIAL: rpm | METRIC: rpm
Used for active drilling IMPERIAL: yes/no | METRIC: yes/no
Two speed gearbox IMPERIAL: yes/no | METRIC: yes/no
Emergency chain drive IMPERIAL: yes/no | METRIC: yes/no
Driven by an independent electric motor IMPERIAL: yes/no | METRIC: yes/no
Electric motor type
Electric motor make
Output power IMPERIAL: hp | METRIC: hp
Maximum continuous torque IMPERIAL: ft-lb | METRIC: m-kg
Associated RPM IMPERIAL: rpm | METRIC: rpm
Drip pan/mud collection system IMPERIAL: yes/no | METRIC: yes/no
Make up torque (if needed) IMPERIAL: lb.ft | METRIC: lb.m
Break out torque (if needed) IMPERIAL: lb.ft | METRIC: lb.m
B.4.1 Auxillary Comments
Make
Type
Maximum opening IMPERIAL: in | METRIC: mm
Rated capacity IMPERIAL: lb | METRIC: kg
Static load capacity IMPERIAL: lb | METRIC: kg
Rotating load capacity IMPERIAL: lb | METRIC: kg
Associated RPM IMPERIAL: rpm | METRIC: rpm
Used for active drilling IMPERIAL: yes/no | METRIC: yes/no
Two speed gearbox IMPERIAL: yes/no | METRIC: yes/no
Emergency chain drive IMPERIAL: yes/no | METRIC: yes/no
Driven by an independent electric motor IMPERIAL: yes/no | METRIC: yes/no
Electric motor type
Electric motor make
Output power IMPERIAL: hp | METRIC: hp
Maximum continuous torque IMPERIAL: ft-lb | METRIC: m-kg
Associated RPM IMPERIAL: rpm | METRIC: rpm
Drip pan/mud collection system IMPERIAL: yes/no | METRIC: yes/no
Make up torque (if needed) IMPERIAL: lb.ft | METRIC: lb.m
Break out torque (if needed) IMPERIAL: lb.ft | METRIC: lb.m
B.4.2 Master Bushings Comments
Make
Type
Maximum opening IMPERIAL: in | METRIC: mm
Inserts bowls (see G.1.7) IMPERIAL: in | METRIC: mm
B.4.3 Top Drive B.4.3 Main Comments
Make
Type IMPERIAL: yes/no | METRIC: yes/no
Rated capacity IMPERIAL: lt | METRIC: lt
Test pressure IMPERIAL: psi | METRIC: bar
Working pressure IMPERIAL: psi | METRIC: bar
Power assignation IMPERIAL: Independent of rotary table | METRIC: mmdependent of rotary table
Number of safety valves IMPERIAL: no | METRIC: no
Working pressure of safety valves IMPERIAL: psi | METRIC: bar
If driven by electric motor
Make
Type
Output power IMPERIAL: hp | METRIC: hp
Maximum continuous torque IMPERIAL: ft-lb | METRIC: m-kg
Associated RPM IMPERIAL: rpm | METRIC: rpm
Two speed gearbox IMPERIAL: yes/no | METRIC: yes/no
Maximum rotary speed IMPERIAL: rpm | METRIC: rpm
Remote operated kelly cock IMPERIAL: yes/no | METRIC: yes/no
Cooling system type IMPERIAL: water / lube oil, etc. | METRIC: water / lube oil, etc.
Makeout/Breakout System
Make
Type
Make up torque max (if required) IMPERIAL: lb.ft | METRIC: lb.m
Break out torque max (if required) IMPERIAL: lb.ft | METRIC: lb.m
Drilling Hoisting Capacity
B.4.3 Auxillary Comments
Make
Type IMPERIAL: yes/no | METRIC: yes/no
Rated capacity IMPERIAL: lt | METRIC: lt
Test pressure IMPERIAL: psi | METRIC: bar
Working pressure IMPERIAL: psi | METRIC: bar
Power assignation IMPERIAL: Independent of rotary table | METRIC: mmdependent of rotary table
Number of safety valves IMPERIAL: no | METRIC: no
Working pressure of safety valves IMPERIAL: psi | METRIC: bar
If driven by electric motor
Make
Type
Output power IMPERIAL: hp | METRIC: hp
Maximum continuous torque IMPERIAL: ft-lb | METRIC: m-kg
Associated RPM IMPERIAL: rpm | METRIC: rpm
Two speed gearbox IMPERIAL: yes/no | METRIC: yes/no
Maximum rotary speed IMPERIAL: rpm | METRIC: rpm
Remote operated kelly cock IMPERIAL: yes/no | METRIC: yes/no
Cooling system type IMPERIAL: water / lube oil, etc. | METRIC: water / lube oil, etc.
Makeout/Breakout System
Make
Type
Make up torque max (if required) IMPERIAL: lb.ft | METRIC: lb.m
Break out torque max (if required) IMPERIAL: lb.ft | METRIC: lb.m
Drilling Hoisting Capacity
B.5 DRILLING CONTROL SYSTEM Comments
Make
Model
Software version
Attached Data Logger Available
External Data Port (Serial/Ethernet) Available on Data Logger
Which (external data port)
Software Protocols Available on External Data Port
(OPC, WITS, WITSML, Profibus)
Serial/Parallel Port for Alarm Printer Available
Ready to Submit? The Spam Check (below) must be completed for the Submit button to appear.
Spam Check: What is 11 + 5 ?* Are you a human or a robot? Please solve 11 + 5 = X?